SWELLSEAL® 2010 is an extruded, vulcanized hydrophilic expansive rubber strip for the sealing of concrete construction joints, pipe penetrations, joints in underground pre-cast elements.
• Sealing cold and construction joints
• Sealing pipe penetrations
• Sealing joints between precast elements
• Sealing vertical construction joints
Figure 1. Swellseal 2010 width
• Proven track record in concrete structures subject to high water pressure
• Reversible swelling properties
• Non-sag when correctly placed around pipes and in vertical joints
• Easily installed by nailing or using SWELLSEAL® WA
• Chemically resistant* *Chemical resistance chart available upon request
|Elongation at break||Approx. 600%||ASTM D412|
|Shore A Hardness||52||ASTM D2240|
|Specific density||1.23-1.27||ASTM D471|
|Swelling capacity in contact with water||100% (10 days)||ASTM D471|
|Water Pressure Resistance||284 psi||DNCC|
|Tensile Strength||1493 psi||ASTM D2240|
|Apperarance||Black rectangular strip of hydrophilic vulcanized expansive rubber||Black rectangular strip of hydrophilic vulcanized expansive rubber|
|Dimensions||⅜” x ¾” (10mm x 20mm)||⅜” x ¾” (10mm x 20mm)|
Note: The data shown above reflects typical results based on laboratory testing under controlled conditions. Reasonable variations from the data shown above may result
Packaging & Handling
1 roll SWELLSEAL 2010 = 32 ft
1 case SWELLSEAL 2010 = 8 rolls (50 lbs)
Unlimited shelf life when stored in a dry place in its original packaging.
SWELLSEAL® 2010 can only function properly in a confined space in order to develop sufficient expansion pressure and assure waterproofing.
The expansion of SWELLSEAL® 2010 will create pressure, which needs to be counteracted by the proper concrete coverage. The required concrete coverage varies from 3.25 inches – 4.0 inches on all sides depending on concrete strength.
SWELLSEAL® 2010 can be applied on both smooth and rough concrete.
|Concrete Strength (psi)||2550||2982||3408||3834||4260|
|Minimum Concrete Coverage||4”||3.7”||3.5”||3.48”||3.28”|
On smooth concrete:
Roll the SWELLSEAL® 2010 between the inner and outer rebar and nail down with a gun (4 to 5 nails per yard) or fix horizontally with SWELLSEAL® WA.
On rough concrete:
Gun SWELLSEAL® WA in a 3/8” bead between inner and outer rebar. Press SWELLSEAL 2010 firmly into the WA. As SWELLSEAL® 2010 is heavy in long strips, especially in vertical applications, apply extra concrete nailing (4 to 5 nails per yard). Install SWELLSEAL® 2010 with the 3/4” surface upwards.
Installation during rain or in prolonged contact with water can result in a premature swelling of the strip, which should be avoided. If SWELLSEAL® 2010 is exposed to water prior to encapsulating in the concrete, allow to dry and shrink back to its original configuration. Important: Roll ends are simply butted together to assure a waterproof seal. Do not install in overlap. The strip needs to be in contact with the joint over its full length.
Health and Safety
Always use protective clothing, gloves and goggles consistent with OSHA regulations during use. Avoid eye and skin contact. Do not ingest. Refer to Safety Data Sheet (SDS) for detailed safety precautions. SDS’s can be obtained from GCP Applied Technologies or from our web site at gcpat.com.
For concrete cover of less than 4 inches, refer to the Installation Procedures for concrete strength requirements. Avoid installing product during heavy rains.
Figure 2. Swellseal WA gunned at 3/8" bead
Figure 3. Swellseal 2010 pressed into Swellseal WA
Figure 4. Swellseal 2010 installed
gcpat.it | Servizio clienti in Italia:: +39 02 93537291
We hope the information here will be helpful. It is based on data and knowledge considered to be true and accurate, and is offered for consideration, investigation and verification by the user, but we do not warrant the results to be obtained. Please read all statements, recommendations, and suggestions in conjunction with our conditions of sale, which apply to all goods supplied by us. No statement, recommendation, or suggestion is intended for any use that would infringe any patent, copyright, or other third party right.
SWELLSEAL is a trademark, which may be registered in the United States and/or other countries, of GCP Applied Technologies Inc. This trademark list has been compiled using available published information as of the publication date and may not accurately reflect current trademark ownership or status.
© Copyright 2016 GCP Applied Technologies Inc. All rights reserved. GCP Applied Technologies Inc., 62 Whittemore Avenue, Cambridge, MA 02140 USA.
In Canada, GCP Canada, Inc., 294 Clements Road, West, Ajax, Ontario, Canada L1S 3C6. G
CP0083 WS-003-1016 Swellseal 2010
Questo documento è aggiornato solo a partire dall'ultima data di aggiornamento sotto riportata ed è valido solo per l'uso in Italia. È importante fare sempre riferimento alle informazioni attualmente disponibili all'URL sottostante per fornire le informazioni più aggiornate sul prodotto al momento dell'uso. Ulteriori pubblicazioni come manuali per i contraenti, bollettini tecnici, disegni di dettaglio e raccomandazioni sui dettagli e altri documenti pertinenti sono disponibili su www.gcpat.it. Le informazioni trovate su altri siti Web non devono essere invocate, in quanto potrebbero non essere aggiornate o applicabili alle condizioni della tua posizione e non accettiamo alcuna responsabilità per il loro contenuto. In caso di conflitti o se occorrono ulteriori informazioni, contattare il servizio clienti GCP.
Last Updated: 2018-11-30